Editorial

Pages i-ii

PDF (300 KB)

Table of contents

Pages iii-iv

PDF (330 KB)

Wear rate prediction of hybrid composites: A comparative study using experimental analysis, finite element simulation, and machine learning prediction _{Original Research Article}

Pages 1-23

Ravitej Y P, Keshavamurthy R, Rahul Kumar, Krantikumar Kshaurad, Balachandra Halemani, Ramakumar Bommisetty, Sripad Kulkarni, Ramesh Shankaranarayana

PDF (1482 KB) 

Parametric optimization of Inconel grades for wire cut electric discharge machining _{Original Research Article}

Pages 24-39

Maria Iruj, Muhammad Tufail, Anis Fatima

PDF (678 KB)

Investigation into synergistic effects of DLC/TiAlN-coated tool and water-based lubrication enhanced with hybrid MXene/Ionic Liquid additive using ironing of stainless steel and tribological testing _{Original Research Article}

Pages 40-54

Mohd Hafis Sulaiman, Muhammad Shuhaimi Ibrahim, Mohd Idris Shah S. Ismail

PDF (1572 KB)

Evaluating surface roughness consistency in UVAM of Inconel 718 via coefficient of variation _{Original Research Article}

Pages 55-72

Norsilawati Ngah, Mohd Shahir Kasim, Siti Nurul Akmal Yusof, Roslan Awang, Afifah Zakiyyah Juri, Raja Izamshah Raja Abdullah, Muhamad Akmal Mohd Zakaria

PDF (1089 KB)

Viscosity behaviour of water-emulsified engine oil for hydrogen internal combustion engine applications _{Original Research Article}

Pages 73-86

Jon Pow Wan, Nur Aisya Affrina Mohamed Ariffin, William W. F. Chong, Jo-Han Ng

PDF (1003 KB)

Tribological characteristics using TiC nanoparticles as surface reinforcement on duplex stainless steel _{Original Research Article}

Pages 87-103

Alin Qistina Shamsuri, Lailatul Hairina Paijan, Zulkifli Mohd Rosli, Jainuddin Ibrahim, Ahmed Nazrin Md Idriss, Aslam Hadi Hamzah

PDF (1368 KB)

Investigation of blended rPET/HPDE and the effect of wall line count using FDM process on mechanical and tribological properties _{Original Research Article}

Pages 104-120

Aslam Hadi Hamzah, Lailatul Hairina Paijan, Mohd Hadzley Abu Bakar, Alin Qistina Shamsuri, Shahrul I. Musa

PDF (914 KB)

Influence of MQL parameters on surface roughness and temperature in end milling of titanium alloy _{Original Research Article}

Pages 121-137

Aiman Nazrin Noor Ismail, Siti Haryani Tomadi, Nor Farah Huda Abd Halim, Mohd Amri Sulaiman, Mohd Reza Zalani

PDF (886 KB)

Optimising HTCS-150 die-machined surfaces: Enhancing surface integrity and manufacturing efficiency _{Original Research Article}

Pages 138-153

Hariz Zuhairi Arif, Mohd Hadzley B. Abu Bakar, Nor Ana Rosli, Lailatul H. Paijan, Mohd Fauzi Mamat, Shaiful Anwar Ismail, Safarudin Gazali Herawan

PDF (825 KB)

Comparative analysis of up and down milling on surface quality and tool life in dry machining of hardened AISI 4340 _{Original Research Article}

Pages 154-170

Baizura Zubir, Jaharah A Ghani, Afifah Zakiyyah Juri, Syed Ahmad Faiz Syed Mohd, Mohamad Sazali Said, Mohd Nizam Ahmad

PDF (732 KB)

Multiaxial compression of stainless steel 304 and its wear behavior _{Original Research Article}

Pages 171-182

Aditya K. Padap, Raeeshul H. Ansari, Narendra Kumar 

PDF (984 KB)

Advances in TiO₂-based composite coatings: Phase control, deposition methods and tribological performance _{Original Research Article}

Pages 183-200

Muhamad Akmal Mohd Sani, Yuslixa Yusuf

PDF (621 KB)

Exploring fly ash and quarry dust particles for next generation anodized coatings _{Review Article}

Pages 201-226

Norliyana Mustapar, Shahira Liza Kamis, Kanao Fukuda, Noor Ayuma Mat Tahir, Yazid Yaakob

PDF (878 KB)

Numerical analysis of AISI 4340 steel machinability under high-speed turning conditions _{Original Research Article}

Pages 227-248

Haniff Abdul Rahman, Jaharah A Ghani, Mohd. Rasidi Mohd. Rasani, Saima Yaqoob, Khairul Aiman Khairul Anuar

PDF (855 KB)

Multi-objective optimization of Botryococcus Braunii based bio-nanolubricant formulations doped with hybrid nano-additives using the MULTIMOORA method _{Original Research Article}

Pages 249-297

Priyanka Singh, Nathi Ram Chauhan

PDF (1006 KB)